CO2 Laser Tube News
- How to carry out daily maintenance of laser tubeIn answer to the requirement from some distributors and partners, hereby we notify the daily maintenance as following:1：The installation of laser tube: Generally the location of laser tube stand shall be at the 1/4 point of the end of laser tube. In the condition of connecting with water cooling sysCO2 Laser Tube News October 11, 2021
- As laser machine manufacturer and distributor, how to choose CO2 laser tube?CO2 laser tube is made of glass and handmade article, theoretically each laser tube is different. Thus as laser machine manufacturer and distributor, how to choose CO2 laser tube? According to practice and experience, Shanghai Puri Laser Technology Co.,Ltd offer the below suggestions: 1.To check thCO2 Laser Tube News July 05, 2021
- How to clean the dirt inside the laser tubeHow to clean the dirt inside the laser tubeAfter working for a period of time, there will be a lot of dirt on the wall of the laser tube water casing pipe and the water pipe. This is caused by the long-term use of the laser tube, the dust, the deposition of cutting materials, and the reproduction ofCO2 Laser Tube News January 05, 2022
- How long is the service life of the laser tube of the laser machine?How long is the service life of the laser tube of the laser machine?Generally speaking, the key to semiconductor lasers is the service life of the laser diode, which is generally more than 10,000 hours. The service life of the laser diode used for communication will be longer. If the solid-state lasCO2 Laser Tube News March 07, 2022
- Installation method of glass CO2 laser tubenstallation method of glass CO2 laser tubeOne: When using, please connect the cooling water first, adopt the principle of low in and high out, adjust the position of the water outlet pipe to ensure that the cooling water is full of the cooling pipe, and there can be no bubbles in the pipe, and thenCO2 Laser Tube News April 07, 2022
- The notice of how to do daily maintenance of laser tubeIn answer to the requirement from some distributors and partners, hereby we notify the daily maintenance as following:1：The installation of laser tube: Generally the location of laser tube stand shall be at the 1/4 point of the end of laser tube. In the condition of connecting with water cooling sysCO2 Laser Tube News August 10, 2015
- The notice of technological upgrading for CO2 laser tubeTo distributors and cooperative partners,From Nov.15th,2012,the chemical formulation of gas have been updated in Shanghai Puri Laser Technology Co., Ltd.We also develop the configuration like the optical materials. It makes the laser tube power stronger and spot pattern more superior.The update doesCO2 Laser Tube News August 10, 2017
- Notice of how to replace the different diameter of laser tubeRegarding to 60W, 80W, 100W, 130W, 160W laser tube, if customers need to replace between different powers, even though the diameters are different, please pay attention that only the laser tube bracket need to be adjusted, and keep the laser path the same.Please download the Puri operation files herCO2 Laser Tube News August 10, 2016
- PURI LASER TUBE GUIDE1,Installation RequirementsLaser tube should be Strictly installed according to the installation diagram, it’s equipped with a dedicated power supply, positive pole is with high voltage, and the starting voltage is 24 kV !Adverse consequences caused by failure to installation: inner tube breakdown bCO2 Laser Tube News August 28, 2018
- Different galvanic current for different power laser tubeIn order to make sure the laser tube lifetime and make it working better, here suggest some galvanic current for different laser tube: 60w: 16-18mA 80w: 18-22mA 100w: 24-26mA 120w: 26-28mA 150w: 28-30mA Note: In the using, the galvanic current can be lower than this, but please do not make it bCO2 Laser Tube News April 26, 2018